www.YamahaR.co.uk

mikef4uk

I see a few posts back you oiled the threads, I'm sure the manual says 'dry', oiling the thread and then tightening to the same torque will cause th…login to view the rest of this post

mikef4uk

I see a few posts back you oiled the threads, I'm sure the manual says 'dry', oiling the thread and then tightening to the same torque will cause the …login to view the rest of this post

mikef4uk

Update, being a little apprehensive I purchased a second ecu, I just had this feeling that it might not go according to plan.............

I did get the…login to view the rest of this post

mikef4uk

Step 2 today
Out for a ride so I could observe the fueling, the man from Dynojet had told me that the Yamaha fuel maps were pretty good, well he's inco…login to view the rest of this post

mikef4uk

So step 1
I got the wideband sensor working with just the autotune module, in the closed loop area (with 02 sensors still active) as expected (and hope…login to view the rest of this post

mikef4uk

Thats the issue, the 'heater' resistors are undersized, warm up, their resistance rises and the ecu switches to closed loop and the bike runs like cra…login to view the rest of this post

mikef4uk

Something like that! At 12V the resistor dissipates about 0.5W, which shouldn't be an issue except that it's been potted. They probably just need to …login to view the rest of this post

mikef4uk

I expect fitting O2 eliminators would also void the warranty as they could cause engine damage, especially if they fail like yours have. Did you get …login to view the rest of this post

mikef4uk

I'm trying to avoid flashing the ecu and loosing my warranty.........a few thoughts

My 23 bike has surprised me with it's ecu refinements after my 16 b…login to view the rest of this post

mikef4uk

I did buy a cheapo ebay reader/reset and it works fine, also reads llve data etc etc, well worth the £35 on later R1 as stuff like setting the fault c…login to view the rest of this post

mikef4uk

For 20 onwards bike, what works please?

mikef4uk

BTW ..... One thing I`ve always wondered ..... a dyno run will normally take a reading from the back wheel , so how do they calculate crank , ( or ge…login to view the rest of this post

mikef4uk

I dont know tbh, I looked into the difference as I also have an Ohlins ERS2 equiped Tuono Factory, that is just about faultless on the road, I picked …login to view the rest of this post

mikef4uk

This was my question....

Has anyone here owned both a 15 -17 bike and changed to a 21 on bike?

The answer is yes, me, I watched more than a few reviews …login to view the rest of this post

mikef4uk

I do tend to start the bike up and run it in the garage if it`s not been used for a few weeks during the winter ...... some day don`t do this , start…login to view the rest of this post

mikef4uk

Mine did similar and one of the fan blades had melted and was catching on the outside of the fan housing,
I suspect it melted during a winter run up i…login to view the rest of this post

mikef4uk

Not the end then after all, another new colour scheme for next year, I have never been a fan of black wheels so I guess I need to buy a left over 23 …login to view the rest of this post

mikef4uk

Thanks for the replies, I have just found quite a good video on youtube from 2020 from Motorcyclist Magazine in Aus, he goes through the various point…login to view the rest of this post

mikef4uk

I asked about Electronic suspension in the 2CR, 2KS part of the forum,

Has anyone here owned both a 15 -17 bike and changed to a 21 on bike?

I'm in…login to view the rest of this post

mikef4uk

Went out with mate (quick rider) with his 17 Tuono Factory (I have a 19 Aprilia but wanted to see how my R1M compared) we did a 220 mile loop into Wal…login to view the rest of this post

mikef4uk

Barton wrote: Sat Oct 07, 2023 6:08 pm Kais or MH racing should be able to change shim stacks.

Kais say they can do anything I want, MH want to set …login to view the rest of this post

mikef4uk

I forgot to add I dropped the front forks by a couple of notches too, I also have a cable tie on the bottom of the forks to measure rebound and that'…login to view the rest of this post

mikef4uk

I had a decent test ride on a MT-10 SP and thought that the suspension was quite harsh, even on the softest setting. A standard 2019 Tuono felt much …login to view the rest of this post

mikef4uk

Cheers Boz,
Yes, played with suspension, tried it in M mode with alterations, bike has never seen any wet stuff and rear moves easy enough but I'll che…login to view the rest of this post

mikef4uk

Or another way to ask the same question
How does 'my' or a 2016 R1M compare to a later 'M' (say 21/22 bike) in the suspension department?

www.YamahaR.co.uk

Search found 696 matches

Re: Rear Axle Bolt & Lock Nut Problems

Re: Rear Axle Bolt & Lock Nut Problems

Re: 2021 on 02 Eliminators

Re: 2021 on 02 Eliminators

Re: 2021 on 02 Eliminators

Re: 2021 on 02 Eliminators

Re: 2021 on 02 Eliminators

Re: 2021 on 02 Eliminators

2021 on 02 Eliminators

Re: Fault code reader/clearer

Fault code reader/clearer

Re: Putting the EXUP back

Re: R1M 2016 v 2023 (or 21 onwards)

Re: R1M 2016 v 2023 (or 21 onwards)

Re: Tick Tick

Re: Tick Tick

Re: End of the R1M?

Re: 2016 R1M Electronic suspension

R1M 2016 v 2023 (or 21 onwards)

Re: 2016 R1M Electronic suspension

Re: 2016 R1M Electronic suspension

Re: 2016 R1M Electronic suspension

Re: 2016 R1M Electronic suspension

Re: 2016 R1M Electronic suspension

Re: 2016 R1M Electronic suspension