www.YamahaR.co.uk

Mufasa92

You need new cables.

The first pic is a bodged repair, they have clamped a broken cable with a bolt through the hole the barrel should locate in.

New c…login to view the rest of this post

Mufasa92

Hello! I need some help getting my old throttle cables on to the new carbs. I didn't find anything related in the manual.

How do I install from this.…login to view the rest of this post

Mufasa92

I’ve had a more thorough look at the oil pan. The oil I can see must be coming from the bolt in the centre of the pan above the headers. You can’t …login to view the rest of this post

Mufasa92

I’ve had a more thorough look at the oil pan. The oil I can see must be coming from the bolt in the centre of the pan above the headers. You can’t se…login to view the rest of this post

Mufasa92

Ok so after much testing, contact spraying, fuse changing and all kinds of diagnostics, I decided to disconect the rear signals and test only the fron…login to view the rest of this post

Mufasa92

Thank for the replies! I will do everything suggested and get back to you. All the things I have tried up until now have been unsuccessful. I took the…login to view the rest of this post

Mufasa92

Hi! A new problem appeared this morning. After putting everything back togheter, I installed the turn signals back on the bike exactly as it was befor…login to view the rest of this post

Mufasa92

This helped me so much. Thank you!

Edit:

Just adding a little bit more info for anyone searching for similar topics.

…login to view the rest of this post

Mufasa92

Thank you very much!

Mufasa92

Hi! I reinstalled the entire EXUP system on the bike because it was missing but I got stuck at the cables. Can someone help me with this? The manual i…login to view the rest of this post

Mufasa92

I never tried to change it like that. I had to remove the headers to also change the water pipe next to the oil filter so it was a 2 in 1 job. Good lu…login to view the rest of this post

Mufasa92

I tested the sensor as you suggested and it worked so I traced the problem back to the wiring. After I separated all the wires and removed the tape I …login to view the rest of this post

Mufasa92

Ye, that means you have to change it. The thing is that there is no guarantee that a used one won't have the same problem after a few miles. The senso…login to view the rest of this post

Mufasa92

Get another one used.

It leaks from the middle of the sensor where the wire goes (black stuff)? Or around it (o ring)?

Mufasa92

I will try that and see what happens. Thanks!

Mufasa92

Hi again! I have one more question. If I put together the brown and blue cables and the fan starts, that means the wires are good and the problem is …login to view the rest of this post

Mufasa92

Hi again! I have one more question. If I put together the brown and blue cables and the fan starts, that means the wires are good and the problem is w…login to view the rest of this post

Mufasa92

Sounds like he messed up the thermoswitch wiring when installing the switch.

If you're not worried about the manual switch, then put it back to standa…login to view the rest of this post

Mufasa92

Hello! I have some problems with the fan. When I first got the bike, the fan wouldn't start no matter what temp it was indicating. I changed the therm…login to view the rest of this post

Mufasa92

I checked them before putting everything back together. They seemed ok.

After getting the carbs back on the bike and installing another TPS, I ran into…login to view the rest of this post

Mufasa92

I opened the carbs and as soon as I pulled them out of the bike, I knew something was wrong. I heard a rattle noise coming from the carbs. It would co…login to view the rest of this post

Mufasa92

sure 4xv same as others hen ignition goes on exup should cycle thru its full movement and return to shut if sticking should not pick up from 7-8000 r…login to view the rest of this post

Mufasa92

Moise wrote:Did you replace the float needle valves?

Sent from my SM-G9208 using Tapatalk

Hmm, no. Do you think this could be it? One of the float n…login to view the rest of this post

Mufasa92

Usually the bog down the bottom end of the Exup is removed or wired open I'm sure it's when they're shut that you don't get full power . . . Usually …login to view the rest of this post

Mufasa92

Thank you for the information and fast reply.

I also sprayed the two identical relays from under the left hand side panel with no changes. After what …login to view the rest of this post

www.YamahaR.co.uk

Search found 33 matches

Re: Throttle Cables Installation

Throttle Cables Installation

Re: Replaced the oil pan gasket - still have a leak

Re: Replaced the oil pan gasket - still have a leak

Re: Electrical Problem

Re: Electrical Problem

Electrical Problem

Re: EXUP Cable Routing

Re: EXUP Cable Routing

EXUP Cable Routing

Re: Replaced the oil pan gasket - still have a leak

Re: Radiator fan problem

Re: Replaced the oil pan gasket - still have a leak

Re: Replaced the oil pan gasket - still have a leak

Re: Radiator fan problem

Re: Radiator fan problem

Re: Radiator fan problem

Re: Radiator fan problem

Radiator fan problem

Re: Won't rev past 8K RPM (4XV)

Re: Won't rev past 8K RPM (4XV)

Re: Won't rev past 8K RPM (4XV)

Re: Won't rev past 8K RPM (4XV)

Re: Won't rev past 8K RPM (4XV)

Re: Speedo and lights dim when other electrics are on