Newbie to this :) 4c8 rider

Benji-still · Post by **Benji-still** » Thu Dec 24, 2015 2:19 pm

the brembo 320mm fully floating discs from Damo once again lol will be fitted with ti front disc bolts pictures to follow soon

Sent from my iPhone using Tapatalk

Benji-still · Post by **Benji-still** » Thu Dec 24, 2015 2:20 pm

got the 5mm spacers on ready for when the bst gets fitted with the over sized discs

Sent from my iPhone using Tapatalk

Benji-still · Post by **Benji-still** » Thu Dec 24, 2015 2:21 pm

tarted up the rear master cylinder a little

Sent from my iPhone using Tapatalk

Post by **jompy** » Thu Dec 24, 2015 2:59 pm

Bling wanker !
those cans look a lot tidier shorter !
everythings looking great

Benji-still · Post by **Benji-still** » Thu Dec 24, 2015 3:36 pm

Yeah I though that jompy didn't like the over hang out the back getting there slowly more pictures soon

Sent from my iPad using Tapatalk

Benji-still · Post by **Benji-still** » Sat Dec 26, 2015 8:33 pm

that's the wheels built up brembo 320mm floating front discs with ti bolts galfer rear disc with ti bolts talon sprocket with ti nuts just tyres to go on now

getting there slowly no rushing with this

Sent from my iPhone using Tapatalk

Post by **Kylezx7r** » Sat Dec 26, 2015 10:05 pm

Looking good mate. Did you torque those Ti bolts up properly? Only asking cause I bought some marchesinis with Ti bolts that had been over tightened and I had to drill 3 out because they stripped the heads

Sent from my iPhone using Tapatalk

Biker123 · Post by **Biker123** » Sat Dec 26, 2015 10:47 pm

Kylezx7r wrote:Looking good mate. Did you torque those Ti bolts up properly? Only asking cause I bought some marchesinis with Ti bolts that had been over tightened and I had to drill 3 out because they stripped the heads

Sent from my iPhone using Tapatalk

Ti bolts can be a pain if not put in properly

Benji-still · Post by **Benji-still** » Sun Dec 27, 2015 9:00 am

Done them up hand tight can get the garage to check them when they go in for the tyres getting put on

Benji-still · Post by **Benji-still** » Sun Dec 27, 2015 9:05 am

Have you got the torque setting for our bike Kyle ?

Post by **Kylezx7r** » Sun Dec 27, 2015 9:31 am

Benji-still wrote:Have you got the torque setting for our bike Kyle ?

I've got the torque value for standard bolts but not Ti
You should be ok as long as your not over tightening

I'm not a fan of loctite but if you are using it use the blue loctite not red.
Red had been used on mine which was part of the problem

Sent from my iPhone using Tapatalk

Post by **jompy** » Sun Dec 27, 2015 9:32 am

Torque settings should be in the service manual downloadable from the 4c8 section , if not the give me your email and I'll see if I get chance to email it to you

Benji-still · Post by **Benji-still** » Sun Dec 27, 2015 9:33 am

Not using loctite Damo said not to I'm not a great fan either I've got them tight then just gave them a little bit more from that

Sent from my iPhone using Tapatalk

Post by **Kylezx7r** » Sun Dec 27, 2015 9:36 am

Benji-still wrote:Not using loctite Damo said not to I'm not a great fan either I've got them tight then just gave them a little bit more from that

Sent from my iPhone using Tapatalk

You should be ok with that , Loctite is a pain in the tits I never use it.

Sent from my iPhone using Tapatalk

Post by **Kylezx7r** » Sun Dec 27, 2015 9:37 am

jompy wrote:Torque settings should be in the service manual downloadable from the 4c8 section , if not the give me your email and I'll see if I get chance to email it to you

That will be for standard bolts will it not?
Ti bolts may be different I'm not sure

Sent from my iPhone using Tapatalk

Benji-still · Post by **Benji-still** » Sun Dec 27, 2015 9:37 am

Lol how you go about doing your ti bolts an nuts up ? You got damo old front callipers now this thread needs to be moved i think lol

Sent from my iPhone using Tapatalk

Post by **Kylezx7r** » Sun Dec 27, 2015 9:40 am

Benji-still wrote:Lol how you go about doing your ti bolts an nuts up ? You got damo old front callipers now this thread needs to be moved i think lol

Sent from my iPhone using Tapatalk

I don't use Ti bolts mate don't really need them on the race bike.
Yeah I got Damos calipers not fitted them yet but will get round to it

Sent from my iPhone using Tapatalk

Benji-still · Post by **Benji-still** » Sun Dec 27, 2015 9:41 am

I'm just putting them on to tidy up the look an keep to the light weight with the wheels [emoji6] well if an when you do sell them front callipers you no where to ask first [emoji106]

Sent from my iPhone using Tapatalk

Benji-still · Post by **Benji-still** » Sun Dec 27, 2015 1:02 pm

Sorry jompy didn't even see you had posted up there is there much fluctuation with torque setting with ti over stock ?

Post by **Kylezx7r** » Sun Dec 27, 2015 1:24 pm

Benji-still wrote:Sorry jompy didn't even see you had posted up there is there much fluctuation with torque setting with ti over stock ?

Benji just had a look in my little book of knowledge and here's some info, I must stress this is not directly referring to disc bolts but titanium bolts in general.

Basically anything that gets hot and then cold again (which your discs do) when using titanium you should use anti-sieze compound and increase the torque value by around 10%

The torque setting for original bolts on your 4C8 is 18Nm

So using that here's what I would do if I was using Ti bolts I would put a small dab of anti-sieze compound on the thread and torque them up to 21Nm and you'll be good to go

If you don't have a torque wrench just a good tight nip will do

Sent from my iPhone using Tapatalk

Benji-still · Post by **Benji-still** » Sun Dec 27, 2015 1:27 pm

Ok I'll grab some anti sieze compound before they go on the bike always get worried with them snapping when getting them tight or stripping them lol

Sent from my iPad using Tapatalk

Post by **jompy** » Sun Dec 27, 2015 4:28 pm

what Kyle said . . . . . i think

Damo666 · Post by **Damo666** » Sun Dec 27, 2015 5:07 pm

When i spoke to ProBolt they said about 30 % less torque which seems odd to me and not correct,anyway i just did it the ole fashioned way of 'feel' then a little nip up,always worked for me as going off Yamaha's torque settings can result in a snapped bolt.....eh Pod

Post by **Kylezx7r** » Sun Dec 27, 2015 5:32 pm

30% less????
Jesus no way would I trust that. My info just relates to titanium bolts in general not bike disc bolts but no way would I be going 30% less. That makes it 12Nm almost finger right

Sent from my iPhone using Tapatalk

Benji-still · Post by **Benji-still** » Sun Dec 27, 2015 5:38 pm

Well the old fashion way it is then

then check after the first ride out

www.YamahaR.co.uk